Codeprt - Pointers - Callback, Can anyone help?

Thank you very much Daniel
Actuly I have to use CDECL in the procedure so it is like this

SUB fpError Cdecl (ByVal MyError As Dword,ByVal MyType As Dword)

End Sub

As the Dll which makes the call back is written in C++, I think it was crashing while trying to clear the stack while leaving the procedure and that is why I was able to see the msgbox and then it was crashing.

Thank you everyone for the support.

-------------
Niraj Bhatt

[Dave Navarro]

Where's your code for scDone? Perhaps that's where it's crashing.

--Dave


-------------
PowerBASIC Support
mailto:[email protected][email protected]</A>

Try using CDECL for your declaration.

-------------
Daniel
[email protected]

Tried that as well but same result, it still crashes after the msgbox

-------------
Niraj Bhatt

[Fred Oxenby]

void fpError(DWORD MyError, DWORD MyType)
=
Sub fpError(Byval MyError as DWord,Byval MyType as DWord)

-------------
Fred
mailto:[email protected][email protected]</A>
http://www.oxenby.se

Daniel,

Thank you...

I have gone past one phase.. Initially it was crashing as soon as there was a callback without proceding inside the procedure now that I have make the correcting as follows:

FUNCTION fpError(ByVal MyErr As Dword, ByVal ErrType As Dword) As long
'OR
'FUNCTION fpError(ByVal MyErr As Long, ByVal ErrType As Long) As long
MSGBOX Str$(MyErr) & "-" & Str$(ErrType)
FUNCTION = 1
END FUNCTION

Now it crashes after going through the procedure, thatis after displaying the msgbox.

If somebody can understand this is the error I am getting:
PRINTE~1 caused an invalid page fault in
module <unknown> at 00de:8178af08.
Registers:
EAX=00000000 CS=015f EIP=8178af08 EFLGS=00010202
EBX=00000000 SS=0167 ESP=0117ff00 EBP=0117ff38
ECX=00000000 DS=0167 ESI=10001f00 FS=4f9f
EDX=8000a310 ES=0167 EDI=8178af08 GS=0000
Bytes at CS:EIP:
07 00 01 00 70 d6 a3 d0 dc fc 17 01 00 00 18 01
Stack dump:
00000008 00000000 00000000 00000000 00000001 8178af08 00000001 d0a45e14 81782b1c 0117fd30 0117ff88 bffbfe14 bff791f0 00000000 0117ff98 bff88ba5


-------------
Niraj Bhatt

As C uses BYVAL parameters per default and PB uses BYREF, you have to specify BYVAL explicitly in your fpError() function.

Regards

-------------
Daniel
[email protected]

I have C proggram as follow:
BOOL Init(FARPROC scDone, FARPROC fpError)
This inisialise one of Mydll which will callback fpError procedure when it detectes some error.
The fpError procedure is as follows:
void fpError(DWORD MyError, DWORD MyType)
{ }

Now I wanted to convert this code to Powerbasic so I did the following:
' Declare the Function
Declare FUNCTION Init LIB "Mydll.dll" ALIAS "Init" (ByVal scDone AS long, ByVal fpError AS long) AS LONG
'Do the inisialisation
i = Init(CODEPTR(scDone),CODEPTR(fpError))
'fpError Procedure
FUNCTION fpError(MyError As long, MyType As long) As long
MSGBOX Str$(TypeErr) & "-" & Str$(MyError)
FUNCTION = 1
END FUNCTION

Now I have tried changing the long Type to DWord but with both types

Whenever there is a callback my progg. crashes.
This works fine in VB with Addressof but I wanted to use PB.
If I do not put the parameters MyError and MyType it does not crash.

Can anyone understand this and help me out.

Thank You




-------------
Niraj Bhatt