Dynamic Callback for CONTROL ADD BUTTON

[Cliff Nichols]

Roberto,
Is what you are describing along the lines of "Scripting"???

AKA
Load a text file, and create a dialog, and have functions act on it????

Possible????....Yes
Programmable???....Yes (depending on your use)
Easy to read???.....NOT ON YOUR LIFE!!!! ( Just kidding, it depends on how much capability you need....but its a doozy even with just basics)


Its a nice concept that I have looked at many times, but the time spent to make it feasible usually runs into a wall and I make a function to be called to cover the process

(Although I will admit being able to "Script" your own code for processes that are similar, but different from the original intent, has long been a side pursuit I wish I had time for)

[Michael Mattias]

However it does seem kind of like a work around as opposed to a more proper way of doing this

Using DDT, this is probably the ONLY way. What you want to accomplish is actually fairly easy to do with SDK-style programming, except SDK-Style does not support "control-level" callaback functions at all, unless you superclass or subclass the individual controls.

However, I have to question your wish to do things this way.

Personally, I'd think about not using control-level callbacks at all, handling everything through the messages sent to the owner window (the dialog itself).

If all you are trapping for buttons is WM_COMMAND, seems to me using control-level callbacks just puts your source code in more places. Since you always know which button is sending the command and you can always store info at the control level using CONTROL SET USER , you can let your primary dialog procedure do stuff based on that value. eg,

CALLBACK  FUNCTION  MY_DIALOG_PROC () AS LONG 
....
SELECT CASE AS LONG CBMSG 
   CASE %WM_COMMAND
      SELECT CASE AS LONG   CBCTLID 
         CASE Id_button1, Id_button2... 
            CONTROL GET USER  CBHNDL, CBCTLID, Subscript TO iValue 
            SELECT CASE iValue 
                CASE 1 
                    do something 
                CASE 2 
                    do something else
                ...
           END SELECT  ' of user value 
     END SELECT  ' of control generating WM_COMMAND

  END SELECT ' of message

MCM

[Roberto Diaz Jr]

I tried the code above, and it took me a few minutes to figure out what "prototype" was, then I finally added a DlgCallback function to use as the prototype.

The program does work as intended, I can create controls dynamically without knowing what callback functions they should link to at compile time. However it does seem kind of like a work around as opposed to a more proper way of doing this. I will continue to experiment with some of the other methods like CONTROL SET/GET USER and see which works the best for my program.

Thanks for for your help.

[Michael Mattias]

want to know if its possible to use a variable or pointer or something as a callback in a CONTROL ADD BUTTON statement

No.

That simplifies things, doesn't it?

What you CAN *try* is...

 CONTROL ADD BUTTON  hdlg, %ID_BUTTON ......   CALL MasterButtonCallback 
 dwProc  =     CODEPTR (ThisBUttonProc) 
 CONTROL SET USER hDlg, %ID_BUTTON, %CB_SUB, dwProc 

 CALLBACK FUNCTION MasterButtonCallback 
  LOCAL dwPRoc AS DWORD 
    CONTROL GET USER  CBHNDL, %ID_BUTTON, %CB_SUB to dwProc
    CALL DWORD  dwProc USING  prototype (CBHNDL, CBMSG,  CBWparam, CBLparam) 
END FUNCTION

CALLBACK FUNCTION ThisButtonProc ()

END FUNCTION

But I think you might be better served to use the CONTROL SET USER values with the "masterbuttoncallback" procedure, and use IF or SELECT CASE on that value in that proc to do different things at different times.

WARNING: This CALL DWORD thing has got to be 'off the reservation' but I would not be surprised if it works; frankly I would be surprised if it doesn't.

However, I cannot in good conscience "recommend" coding this way. I'd go with the CONTROL SET/GET USER thing.

MCM

[Roberto Diaz Jr]

I want to know if its possible to use a variable or pointer or something as a callback in a CONTROL ADD BUTTON statement. Below is an example of what I've tried doing but didn't work.

#COMPILE EXE
#DIM ALL

TYPE DialogObject
   dHandle                    AS DWORD
   dText                      AS ASCIIZ * 65
   dWidth                     AS INTEGER
   dHeight                    AS INTEGER
END TYPE

TYPE ControlObject
   cID                        AS DWORD
   cCallback                  AS DWORD
   cType                      AS ASCIIZ * 33
   cText                      AS ASCIIZ * 33
   cXPos                      AS INTEGER
   cYPos                      AS INTEGER
   cWidth                     AS INTEGER
   cHeight                    AS INTEGER
END TYPE

FUNCTION addControl(BYVAL myControl AS ControlObject, BYVAL myDialogHandle AS DWORD) AS LONG
   SELECT CASE LCASE$(myControl.cType)
      CASE "button"
         CONTROL ADD BUTTON, myDialogHandle, myControl.cID, myControl.cText, myControl.cXPos, myControl.cYPos, myControl.cWidth, myControl.cHeight CALL DWORD myControl.cCallback
      CASE ELSE
         ' Do Nothing
   END SELECT
END FUNCTION 

CALLBACK FUNCTION button_Exit() AS LONG
   IF CB.MSG = %WM_COMMAND THEN
    IF CB.CTLMSG = %BN_CLICKED THEN
      DIALOG END CB.HNDL
      FUNCTION = 1
    END IF
  END IF
END FUNCTION 

FUNCTION PBMAIN()
   ' Variable Declaration
   DIM dMain                  AS DialogObject
   DIM cExit                  AS ControlObject

   ' Initialization
   dMain.dText                = "Test Program"
   dMain.dWidth               = 250
   dMain.dHeight              = 300
   cExit.cID                  = 1001
   cExit.cCallback            = CODEPTR(button_Exit)
   cExit.cType                = "button"
   cExit.cText                = "Exit"
   cExit.cXPos                = 5
   cExit.cYPos                = 5
   cExit.cWidth               = 240
   cExit.cHeight              = 24
   
   ' Dialog Creation
   DIALOG NEW PIXELS, 0, dMain.dText, , , dMain.dWidth, dMain.dHeight TO dMain.dHandle
   addControl(cExit, dMain.dHandle)
   DIALOG SHOW MODAL dMain.dHandle
   
END FUNCTION

Main reason I want to do this is for creating dynamic buttons which might point to different callback functions based on external data (for example a config file or something). I know ways around it could be creating a dialog callback and then just doing stuff in there based on which button was pressed or using a macro perhaps. Either way any help, comments are welcome. Thanks.